EP manufacturer substitution gearbox for woods rotary gearbox
NEW 40 HP GEARBOX Smooth Enter 1 three/eight 12 spline output Interchangable with market well-liked size i.e.: OMNI GRIZZLEY CHEETAH HOWSE KING KUTTER BUSH HOG HICO SILVER EDGE Numerous More
Attributes
(one) brand name new forty five horse power shearpin gearbox. This gearbox suits a number of diverse tends to make of 4′,5′ and some 6′ rotary cutters. I sell a great deal of these containers each 12 months for many different programs and carry ALL Alternative Areas for this box, but with any luck , you will not have to be concerned about that.
Here are the specs on the box:
*45 horse electrical power gearbox
*Normal one-3/8″ smooth input shaft(where the pto shaft hooks on). The pto shaft is held on by a one/two shearbolt.
*length of the input shaft out of the gearbox is three” prolonged
*bolt hole pattern for mounting is on the corners, 4-three/4 centre of gap to heart of hole. It normally takes a 5/8″ bolt.
*twelve splined output shaft(exactly where the blade carrier hooks up on the bottom)
*1-nine/sixteen outdoors measurement above the output shaft splines- from the foundation of the output cap to the finish of the splines is two-3/four” long- general length of the output shaft is 4-one/2″ lengthy.
*will take a 1″ threaded castle nut and a carter crucial on the base of the output shaft to safe blade pan(NUT is provided – – BLADE PAN IS NOT!!)
*overall height of the box from the best of the mower deck to the best of the box is nine-1/two”
This is a pretty weighty merchandise (forty seven lbs.) so freight is not low cost, but we do not make anything off of freight, whatsoever ups costs us we cost you.
40 HP
1:1:47 Ratio
1-3/eight” Easy Enter Shaft with Shear Pin Hole
1-1/2″ twelve-Spline Ouput Shaft
Bolt Pattern: six-one/2″ (4) five/8″ Holes, 5″ Heart Gap Required for Shaft Assembly
The Input and Output Shafts Cannot be Acquired Serparately.
They are Offered as a package.
The kit consists of the following components: input shaft, input equipment, output shaft, output gear.
The Shaft Kit Can’t Be Divided.
EP model 
replacement gearbox for woods rotary gearbox
Rotary Cutter Gearbox Troubleshooting Manual
Is your mower leaking, creaking or normally performing improperly? You’ve come to the proper area.
Read through below for the most typical issues with rotary cutter gearboxes and their remedies (from quick and soiled, to specialist).
Leaking Bottom Seal:
If you’ve wrapped some baling or fencing wire all around your output shaft and blown the seal, the skilled point to do is to substitute the seal.
If your output seal is intact, and you are capable to get ID, OD and thickness measurements (in millimeters), most bearing residences can purchase you up a generic double-lip seal that will get you back again up-and-operating. If not, give us a call and we can assist you kind out what you want.
A dental select is the best way to get rid of the old seal prior to pressing in the new one particular.
If you happen to be fortunate ample to have a sluggish-leak, the rapid and filthy method is to run automotive-sort grease in the gearbox until finally the new seal comes in. Be confident to check and add grease a lot more often than you would with oil, as this is NOT a skilled restore.
Broken Output Shaft:
Uh oh. You strike some thing that failed to go. The very good information is that the output shaft on most gearboxes is pretty effortless to replace. The bad information is… it’s hardly ever an isolated failure.
The 1st thing to do is to take apart your gearbox and evaluate the total extent of the damage. If it is truly just the output shaft, you need to be able to alter it out, no issue. The output shafts start at about $70 and go up in price tag relying on the size of the gearbox.
Even so, in most cases, the bearings ($twenty/ea), seals ($ten/ea) and equipment-set ($70) will also typically get a beating. If you might be unfortunate, the output cap ($80) will also experience some harm.
In this scenario, it is typically cheaper to exchange the gearbox. Assess the cost of areas to the value of an entire, new, warrantied gearbox. Sometimes, even pros have to know when to call it a working day.
I Want to Modify my Input Shaft:
If you are tired of altering shear pins or looking back again and seeing that your mower hasn’t been chopping, you might want to put in a slip-clutch pto shaft (Yes, we offer these way too).
This generally requires installing a 540-fashion, 6-spline enter shaft ($eighty five) on your mower’s gearbox.
Lucky for you, we did a create-up on our weblog. It really is named “How to adjust the input shaft on your rotary cutter gearbox”.
My Gearbox is Groaning/Creaking:
“Groaning”, “creaking”, or “popping” all audio kind-of similar above-the-cellphone. The greatest thing to do is to disassemble your gearbox and take a look at the gears and bearings. The issue will usually existing alone in the way of broken/missing equipment enamel, toasted gears (like that photo on our home page), or blown bearings.
If almost everything appears standard, try out altering the gear-mesh. This is accomplished with the mylar “gaskets” that sit in between the main gearbox circumstance and the input/output caps. Attempt adding or removing some of these spacers right up until your gears have about 1/eight”-one/4″ of free of charge perform. Pros can order replacements ($1-2) in varying thicknesses, but we advocate the fast and dirty approach of reducing your very own out of a sheet of mylar.
Never overlook to re-seal the gearbox with RTV soon after you’ve found the appropriate blend. Even however they’re named “gaskets”, they will not seal your gearbox on their possess.
If just recently you, among your close friends or household participant had any kind of experience with Gearbox For Fertiliser Spreaders, don’t think twice to discuss your opinion in remarks.