The EP Series Helical Bevel Reducer provides unmatched performance, durability, and design flexibility. This unit offers torque capacities up to 20,000 Nm (14,750 ft lbs).
The cat4CAD software allows simple interactive product selection of the complete gearbox and gear-engine system. Cat4CAD supports you in selecting and configuring these products, provides you the opportunity to print out comprehensive technical data bedsheets, and generates complete 2D drawings and 3D versions for direct download.
11 sizes
Input power capacities from 0.16 to 120 HP
Gear ratios from 5:1 to 8900:1
Torque capacities to 20,000 Nm
Inverter duty course F insulated motor windings
Course 12 Helical and Spiral Bevel Gears: Provides higher efficiencies and greater torques in smaller sized sizes.
Multiple Input Options: Essential gear motors, in . or metric shafts, NEMA, IEC, and servo adapters provide unmatched drive versatility.
Multiple Output Options: Hollow bores and shrink disks for shaft mounting, inch and metric output shafts, installation pilots and flanges provide an array of design solutions.
UNIBLOCK Housing: For optimum rigidity, helical bevel gear reducer universal mounting on five sides or with a torque arm.
Worldwide Motor: Multiple leads and windings for worldwide multi volt/Hz requirements in addition modular design to accept brakes, encoders or forced cooling.
High efficiency motor design available
Innovative self-locking, self-aligning taper shaft engine connection
Gearbox supplied factory filled up with synthetic oil
Corrosion and shock resistant cast iron housing
High efficiency helical-bevel gears. 98% per stage
Normally closed breather with multiple locations (Optional OtN2000)
Double lip seals upon heat treated, plunge surface shafts
Shaft mounting options include tapered bushings designs
This is a thorough offering of energy-efficient, right angle helical bevel enclosed gearing. It is obtainable as gearmotors and a number of reducers with torque capacities up to 119,000 inch pounds. Housing styles include footed, encounter and flanged configurations. Gearmotors are available in three stage high efficiency designs through 50 HP and single phase to 5 HP. We provide a variety of input and result shaft choices. Additionally, you will find fixed and variable rate motors and range of ratios obtainable in this product offering.
Features
Accommodates insight power from ΒΌ Hp to 75Hp
Torque rankings up to 119,489 in-lbs
Decrease ratios up to 7,500:1
Helical – bevel – helical gear train offers affordable high and low speed solutions
Up to 94% efficient
Four input options available for all units
Two output flange options – B5 and B14
Multiple output shaft interfaces
Essential dimensions interchangeable with major competitors
Modifications / Accessories
Integral Gearmotor
Clamp Collar C-Face Input
Solid Shaft Input
3-Piece Coupled C-Face Input
CEMA Screw Conveyor Adapter
EZ Kleen Washdown Package
XT Output Seals
Backstop
DURABLE Output Bearings
Inch or Metric Dimensions
Common Applications
Troughing Belt Conveyors
Slider Bed Conveyors
Mixer Drives
Screw Conveyors
Bucket Elevators
General Industrial Machinery
Common Industries
Aggregate and Cement
Air Handling
Chemical, Oil, and Gas
Food, Beverage, and Pharmaceutical
Paper and Forest
Unit and Baggage Handling
Water and Wastewater
As per the growing and varying needs of customers, you can expect an array of Helical Bevel Equipment Reducers. The technological content of our products permits an extraordinary performance/lifespan ratio. The extremely versatile Helical Bevel Gear Reducers we offer are successfully found in a vast number of commercial and civil applications. They are B-Series units that offer excellent value for money and result torque/weight ratio, especially due to the fact they need not a lot of servicing. Besides these, our products are available in cast iron (sizes 063 to 163) or light weight aluminum (sizes A42 to A73) casing.
Features:
Sizes: 060-080-100-125-140-150-160
Available versions: B-fitted for motor coupling, IB with input shaft, CB with compact motor, PB-fitted for electric motor coupling with flexible joint
Casing with ft FC, flange SC and general UC
Power up to 90 kW
Gears hardened and tempered with shaved or floor profile
Gearing with 3 reduction stages
Gleason spiral bevel equipment pairs with run-in profile, mounted as second decrease stage for an increased resistance
Reduction ratios between 5, 71 and 187, 24
Torque max 13.000 Nm and admissible radial loads max 80.000 N
High-power casings optimized with FEM evaluation and input and output flanges of grey cast-iron G200 to make sure top level performances and high reliability
Load capacity calculated and verified according to ISO 6336 and AGMA 2001
Painted with RAL 5010 blue epoxy-polyester powder
Accessories: torque arm, output flange, output shaft, shrink disk, backstop device, protection cover package, viton essential oil seals, reinforced result, assemble/disassemble kit
Series EP right angle helical bevel gear motors offer ratios from 8:1 to 160:1 in three levels or up to 10000:1 in five phases. Motors are available up to 90kW and output torque capacity up to 12,300 Nm.
The series EP helical bevel gear motor was created with integral cast feet for base or end mounting and can be offered with single or dual extended output shafts.
Devices are also available as shaft mounted or with result flanges and are available for mounting horizontally or 
vertically. The units can also be offered with a bolt on torque response bracket and all variants can be found possibly motorised or with an input shaft assembly.
Adding to the brand new selection of Ever-Power helical equipment motors this product takes advantage of our a long time of accumulated design experience together with the use of top quality materials and components. The outcome is a number of velocity reducing geared motors providing high load having capacities, increased efficiency, silent running and reliability.
Features of Helical Bevel Gear Motor
Standard motor connection
Capability to fit double oil seals, on insight and output shaft because required.
All units are dimensionally interchangeable with additional major manufacturers.
Units are produced and assembled from a family of modular kits for distributor friendliness minimizing inventory and maximizing availability.
Motorized units could be fitted with a backstop module and reducer Products can be installed with a backstop and fan.
Applications:
-Conveyors, Agitators, Elevators, Cranes, Crushers
-Helical Bevel gear motors are used in industries such as chemical substances, pharma, packaging, food processing, plastic and automation etc.
Key Features:
Sizes: A40-A50-A70
Offered versions: EP – fitted for motor coupling, IEP – with input shaft, CEP – with compact motor
Cases with foot, flange or universal
Power up to 4,8 Kw
Gears with shaved or floor profile
Gearing with 2 and 3 reduction stages
Hypoid bevel gears for size A40 and A50, gleason bevel gear pairs for size A70, all with run-in profile
Reduction ratios between 7,62 and 442,76
Torque max 450 Nm and admissible radial loads max 5.500 N on hollow shaft and 10.000 N on solid shaft
Cases in die-cast aluminium alloy
Superb mechanical strength while being and particularly lightweight
Load capacity calculated to ISO6336 and verified according to AGMA 2001-B88
Painted with RAL 5010 blue epoxy-polyester powder in according to DIN 1843
Accessories: torque arm, result flange, output shaft.
Generallntroduction of HK series:
Gear Reducer
The EP series gear units, are novel transmission gadget and composed of Y series engine, helical gear,Arc gear and worm gear. The gears are made from high wear-resisting alloy components, specifically and finely processed.
Advantages:
1: Helical-bevel equipment two-stage reducer
2: Compact structure, high efficiency
3: Quenched 20CrMnTi for gears
4: CE, ISO9001.
5: Compact design, small volume, nice appearance ,and solid capacity to be overloaded.
6: Precise division and wide range for transmission ratio.
7: The effectiveness is up to as high because 96% with low energy usage, strong adaptability and is capable of operating continually in corrosive or damp environment.
8: All- purpose make use of, convenient and low-price maintenance.
9: New seal device, strong adaptability.
10: Varied selection of motor combinations, mouting positions and struture projects.
